how to nail into concrete floors

Attaching plywood subfloor to concrete slab : General ...- how to nail into concrete floors ,Jan 16, 2010·Just place them on the slab in rows, offsetting the joints, perpendicular to the direction you want the wood flooring installed. Be sure to allow at least 1/4" gaps between each panel and about a 1/2" gap at the walls. The weight of the flooring and nailing the flooring into the plywood panels keeps everything flat and together.Best Way to Drive a Nail Into Concrete - YouTubeMar 27, 2014·Leah from See Jane Drill demonstrates how to drive a nail into concrete to attach a wall to a cement floor, using a powder-actuated strike tool. This tools ...



Can I nail through floor leveling compound?

May 27, 2020·4.5/5 (1,574 Views . 14 Votes) Some self-levellers can be nailed through, others you can't. So if you're installing hardwood flooring over top, you will need a self-levelling cement that you can nail through. Also, some products can have tiles installed on top, others require a decoupling membrane on the substrate before the cement can be poured.

How To Attach Bottom Plate To A Concrete Floor – Home ...

Attaching the bottom plate of a wall to a concrete floor can be done using any of the following methods: Cut nails (aka masonry nails) Concrete nails. Concrete screws. Wedge anchors. Construction Adhesive. No matter the reason, attaching a 2×4 bottom plate to the concrete …

How to Use Common Nails to Attach Wood to Concrete

CLICK HERE to get FREE & FAST BIDS from carpenters who can drive nails into concrete. Concrete Nails Can Be Regular 16d Sinker Nails. You can use regular 16d sinker nails as concrete nails in an upcoming project where you need to attach a piece of treated lumber to a poured concrete slab or a wall. The wood could be a 2 x 4 bottom plate for a ...

Choosing the Best Anchor to Fasten to Concrete - Concrete ...

Nov 24, 2020·A 1/2" concrete wedge anchor will not through a 1/2" hole in a fixture. The threaded part of the anchor will fit through the 1/2" hole but not the working end. The concrete anchor diameter is matched to the hole size that needs to be drilled into the concrete to allow the anchor to protrude through the fixture.

Removing studs nailed into concrete basement floor ...

Jul 01, 2018·When fired into concrete, the friction turns the concrete around the nail to glass, therby fusing the nail. The nail shown in your picture is a powder actuated nail, and most can be removed by shattering the glass that holds it. Hammering the nail usually works, then pry it out with a crowbar.

How to Drive Nails into Concrete by Hand

May 12, 2021·Drive the Nails. Reposition the board over the pilot holes, aligning the board with the marks on the floor. Insert concrete or masonry nails into the holes, and drive them flush to the surface of the wood using a framing hammer. Be careful not to bend the nails …

How to Install Transition Strips on Concrete Floors | Hunker

Transition strips are used to finish hardwood and laminate floor edges where the product meets an existing floor in a doorway, and are typically cut to fit and then nailed in place or snapped into a track that has been screwed to the floor. When you're working on a concrete floor, the installation of transitions is different from the way it's ...

How to anchor to concrete that has radiant floor heating ...

The tubes are tied to wire mesh on the bottom of the slab and likely below at least 2 inches of concrete, but I'm speaking based on our technique. We secure interior timber frame walls to the concrete with construction adhesive and a ramset with 1.5 inch nails. The nail goes through about 1 inch of wood, and penetrates 1 inch into the concrete.

Best Way to Drive a Nail Into Concrete - See Jane Drill

Nov 12, 2015·November 12, 2015. Best Way to Drive a Nail into Concrete.Learn how to drive a nail into concrete quickly and easily, using a powder actuated strike tool (sometimes called by one of its brand names of Ram Set). This tool can also be used to drive a nail into structural steel and masonry.

Drilling, Nailing, Screwing: Can They Cause Cracks in ...

Sep 02, 2010·Nailing. For nailing into concrete and not causing concrete cracks a concrete nail gun is the best option. It runs on compressed air so it has the force to push a nail firmly into the concrete. It’s the method that’s least likely to cause concrete cracks, although no method is infallible. As it’s done quickly, with a much smaller hole ...

Ramset HammerShot 0.22 Caliber Single Shot Tool-00022 ...

We bought 3" nails for it. On the portions of the floor with new concrete it worked very well and drove the nails all the way in. In the 50 year old concrete areas the nail made a dent in the concrete and then bent over. We ended up using a combination of this and Tapcon screws depending on which concrete we were attaching to.

Ramset MasterShot Powder Actuated Tool – How To Nail It ...

May 26, 2015·The Ramset MasterShot .22 Caliber powder-actuated tool was designed to make attachments to concrete and steel fast and easy. The MasterShot is capable of sinking nails from ½” – 3” long through steel, wood, and concrete. The “powder-actuated” end of the equation comes in the form of .22 caliber single shot powder loads.

How To Attach Bottom Plate To A Concrete Floor – Home ...

Attaching the bottom plate of a wall to a concrete floor can be done using any of the following methods: Cut nails (aka masonry nails) Concrete nails. Concrete screws. Wedge anchors. Construction Adhesive. No matter the reason, attaching a 2×4 bottom plate to the concrete …

Best Practices for Attaching Wood to Concrete | Concrete Decor

Feb 07, 2018·Nails. The easiest approach is simply to nail the wood to the concrete. Two common nail options are shown below: the cut nail and the concrete nail. The cut nail has a square, tapered shape with a square tip. These nails are driven through a board and into concrete underneath, much like nailing a wood board to a wood floor.

carpet - Setting tack strip in concrete - Home Improvement ...

Nov 22, 2019·I helped a friend lay carpet for two years. We used the tack strip with concrete nails with no adhesive, but I could see how the condition of the concrete might require it. The key we found was that you have to get the nail into the concrete in one hit. Multiple hits with the hammer will just cause the concrete to crumble.

Fastening Subfloor Plywood To Concrete Slab | DIY Home ...

Jan 15, 2009·But I said I am assuming the standard 1.5 rough flooring and he is proposing 3in to account for all that subfloor work? Again this is above grade and a concrete pad foundation in a moderate no frost area. I am thinking 12 nails per 4x8 subfloor. Looked at engineered wood flooring and it looks like artificial wood!!

Tack strips to concrete, and what the heck, Home Depot ...

Jun 20, 2018·Concrete tack strip (already has concrete nails) are typically used. However, having nailed the stuff myself, it can be an absolute PITA depending on the concrete. The nail either goes in nice and easy, or you need excessive force to even do anything, the …

Gripper strips on a concrete floor | Screwfix Community Forum

Jan 17, 2018·How can I do this properly? having spent hours removing the old (glued) carpet I don't want to use glue again, when I try to nail down gripper strip some of the nails go into the floor, and the the rest simply make a 2 inch hole in the concrete.

How to Drill Into Concrete - The Home Depot

Don't let a concrete wall or floor stop you from completing your project. Learning how to drill through concrete can seem difficult, but what looks like a challenging job can be made simpler with the right tools and proper technique. This guide reviews how to drill into concrete safely and effectively.

How To Attach Bottom Plate To A Concrete Floor – Home ...

Attaching the bottom plate of a wall to a concrete floor can be done using any of the following methods: Cut nails (aka masonry nails) Concrete nails. Concrete screws. Wedge anchors. Construction Adhesive. No matter the reason, attaching a 2×4 bottom plate to the concrete …

Concrete anchoring nails????? - Fine Homebuilding

Nov 22, 2009·Drill 3/16" hole 4" deep thru the lumber and into concrete.The 4" is from the top of the plate. Place a piece of rebar tie wire about 4" long in the hole,then a 16d galvanized or bright nail ( galvanized is better but has a tendency to bend ).Drive the 16d nail thru lumber into hole and the wire will deform and take up any slop in the hole.

Tack strips to concrete, and what the heck, Home Depot ...

Jun 20, 2018·Concrete tack strip (already has concrete nails) are typically used. However, having nailed the stuff myself, it can be an absolute PITA depending on the concrete. The nail either goes in nice and easy, or you need excessive force to even do anything, the …

How to Install Transition Strips on Concrete Floors | Hunker

Transition strips are used to finish hardwood and laminate floor edges where the product meets an existing floor in a doorway, and are typically cut to fit and then nailed in place or snapped into a track that has been screwed to the floor. When you're working on a concrete floor, the installation of transitions is different from the way it's ...

Fastening Steel Stud Track to Concrete Basement Floor ...

Dec 08, 2011·I noticed that whomever installed the tile floor layed a green colored paper between the concrete and the thinset for the tile floor. I assume this is some sort of vapor/moisture barrier, but I don't know which kind exactly. I was looking into applying something like Redgard to the concrete where I will be installing the new stud track and tile.